SRAM AXS Mobile
Welcome to the feedback portal for SRAM AXS App. We want to hear your feedback!
- We will email you with updates on your feedback and/or requests.
- You can change your preferences in Settings if you would not like to be contacted.
227 results found
-
Shifter low battery notifications when new batteries installed
My shifter batteries were low so I replaced them. Once replaced I went into the AXS App, woke the components up and it showed these as being full. I went for my ride the next day and once completed I received notifications to say the shifter batteries are low. I once again logged into the app and it shows the batteries as full but I still get notifications to say that the shifters are low after every ride. Anyone else have this issue?
21 votes -
Sequential shifting
My other bike with Di2, when connected to my Garmin (other compatible brands should be included), I get a beep warning me that my next shift will activate the front auto shift. I also get an alert when I reach the last sprocket (small or large) that I'm out of gears.
It would be very useful for AXS to do the same.21 votes -
More Sequential AND Compensation options. I want to use Compensation mode, but also lock out various combinations to prevent cross-chaining.
In Compensation mode, if I select the second largest or largest (user choice) sprocket with the big chainring, I get a sequential shift on the chainring instead.
16 votes -
Show quarq indepenant leverage on crank rotation for RH and LH crank rotations
On garmin device get independent leg crank power around each revolution of the crank. Garmin call this power phase.
16 votes -
Stop deleting existing bike profiles when updating sram axs app
Twice now that I've lost my bike profile when updating the sram axs app. Please test each release properly before it goes out.
16 votes -
15 votes
-
Change gear on the App
I've had AXS for 7 months and while I was out last week the shifter battery went flat (I was expecting it to last a year). I was 10 miles from home and found a CR2032 battery in an emergency rear light I carry in my pack so got going again. If not for this I would have been stuck in the last gear I was in which may not be ideal for limping home. If it was possible to select a gear from the app then a compromise gear could be selected, and even changed now and again if…
15 votes -
Offline Mode for the Mobile App
Create an offline mode for the app in order to review the status and configuration settings from one's last ride. Without being connected to the AXS components.
15 votes -
Make the AXS Eagle shifter a true 3 button shifter.
I have the AXS Eagle and Reverb and I can't for the life of me combine them. The AXS shifter says it has three buttons that I can customize, but the app/system doesn't let you combine the shifter up/down and Reverb actions all into one shifter. SRAM should just say the shifter has 2 buttons, not three.
15 votes -
Step 1 of the AXS Search instructions is unhelpful.
Pair your SRAM AXS system per the user manual...could you at least put a link to the manual or a video? Now I have to go and scour the internet for this information....walk me through the process please!
15 votes -
Enable any function to be assigned to any number of levers/buttons/blips
At the moment there is some weird exclusivity where I can't pair certain shift functions to more than one button, in particular I think it's upshift can't be paired to my left paddle as well as a blip on the right shifter assembly. This negates the point of having blips.
14 votes -
Force AXS Rear derailleur - stop working
I updated my Force Etap AXS on January 19, 2023, to firmware 2.41.0. I used the bike normally on the 21st, but today when I went out to ride the rear derailleur was not working. I thought it was the battery but after replaced it the problem continues. When installing it the derailleur light stayed ON and remained without working. I also couldn't connect it with the AXS App.
After doing a search on the internet I saw that I should remove the battery, hold the button and install the battery again, this way it would connect to the APP.
…
13 votes -
The app should remember battery levels (perhaps show the aging of the battery level)
The app should remember the battery level from the last connect - allow me to see it days later (show the aging of that level or a timestamp of the battery level). It's frustrating that I cannot see the battery level after component disconnects from BlueTooth.
13 votes -
Add the Hammerhead Karoo (V2) to supported devices
Add the Hammerhead Karoo (V2) to supported devices in addition to garmin and wahoo. The Karoo is rapidly gaining market share and ideal for exploring new grounds. For me personally having insights on my gravel bike would be great
13 votes -
Longer awake times
Components are awake for 30 seconds before switching off and it's quite often components take longer than the 30 seconds awake time to connect to the app requiring multiple wake ups before they eventually connect. A solution would be an optional in app feature or firmware update to lengthen the awake time to prevent components cutting out whilst in the connecting phase.
12 votes -
Automatic firmware updates
It would be nice for firmware to update across all 4 devices in the background, whenever you are riding and your phone is nearby.
12 votes -
Provide a better way to monitor Shift lever battery life in the AXS App
The battery levels shown in the AXS App for the Shift levers are often grayed out making it difficult to know current battery status
12 votes -
Allow app to pair components
It would be nice if the app could pair devices to the derailleur when added to a bike. For instance if I have a bike with Eagle AXS setup and add a Reverb AXS in the app if the app could also pair it to the derailleur so I can setup the buttons without going through the AXS pairing process.
12 votes -
Force AXS on sequential changes up from large to small chainwheel
My Force AXS shifts from large to small chainwheel when moving from gear 2 to the largest cog (1). I would like it to do this between cog 4 and 3 as this would be more useful for shifting to further low gears plus it will ensure a better chain line ie less crossed than large chainwheel to cog 2 and 3.
11 votes -
More choice with compensation shift
I would like to add the choice to use the compensation shift only when down shifting or only when upshifting with the FD and not only in both directions as it is now.
11 votes
- Don't see your idea?